Analog way Pulse LE User Manual download pdf

QUICK START GUIDE

What’s in the box

Quick install and setup

Thank you for choosing Analog Way and the Pulse LE. By following these simple steps, you will be able to setup and

use your powerful Scaler/Switcher within minutes. Discover the Pulse LE extensive capabilities and intuitive interface

while conguring your rst show, and unleash your creativity for a new experience in show and event management by

Analog Way.

Pulse LE - Ref. PLS200

1 x Pulse LE (PLS200)

1 x Power supply cord

2 x DVI male to HD15 female and DVI-D female breakout cable

1 x HD15 to 5 BNC cable

1 x Ethernet cross cable (for device update)

1 x Set of 3 audio 5-pin screw terminals

4 x Screws for handle removal (M4x12mm)

1 x RCS - Remote Control Software (for PC only) *

1 x User Manual (PDF version) *

1 x Quick Start Guide (PDF version) *

* Download on our website: www.analogway.com

Getting started:

You may wish to reset the unit to factory settings to get started.

Go to: Menu --

Control --

Default Values --

Yes.

1. Select the Output resolution that matches the native

resolution of your display. You will next be prompted to

choose enable follow mode if desired and output rate.

Output

Output format

1024x768

Internal Ref --

60 Hz.

2. InputscanbeconguredautomaticallyusingtheAuto Set

All function.

Intputs

AutoSet All --

Yes.

It will scan each input and detect the sync type that is

plugged in. You can still do an Autoset or manual setup

per input.

The Pulse LE has 2 layers available called: [BACKGROUND

LIVE], and [PIP]. Each layer will obscure your view other

layers below.

3. To display a source, Select the [BACKGROUND LIVE]

layer (it will begin to blink) then, select a source (it will

also blink). Press [TAKE] to transition your source from

preview to program output.

There will always be a layer selected (blinking) and a source

selected (blinking) to the selected layer (blinking). To view on

preview or change the contents of a different layer, simply select

it. Only 1 layer can be seen on the preview at a time.

4. To display a PIP, select the PIP layer (it will begin to blink)

then select your source (it will also blink). Press [TAKE] to

display the PIP on program output.

To see the layer beneath, you will need to clear or move the

layers that are on top.

5. To clear the PIP or any other layer, select the layer (it will

blink) then, select [BLACK]. Press [TAKE] to remove the

layer from the program output.

*TIP* If you would like the Program and Preview to toggle/

ipop during each Take, enable this feature by going to

Control

Preset Toggle.

Once enabled, everything on the Program output will become

the Preview during each Take.

PLS200 can be used to display:

- sources seamlessly switched in the Background Live layer.

- 1 PIP over the Background Live layer.

- 2 PIPs over the Background Color (Split Screen).

IMPORTANT: Simply selecting a menu item will not set it to

that value. Be sure to press the ENTER button when para-

metering the menu items.

WARNING !

If required, front handles of the device can be dismantled,

but with caution.

The original screws removed must not be reintroduced to

their location without handles in place.

Substantial damages can occur, including risk of elec-

tric shock from the mains voltage.

Only M4x12mm screws can be used.

(They are supplied with the unit)

1 2 3 4

Summary of Contents

Page 1 - WARNING !

QUICK START GUIDEWhat’s in the boxQuick install and setupThank you for choosing Analog Way and the Pulse LE. By following these simple steps, you will

Page 2 - Front Panel Description

Pulse LE - Ref. PLS200Front Panel DescriptionEXIT/MENU: Home Menu or back one levelENTER: Validates the menu or commandSelect a custom transitionPress

Page 3 - Rear Panel Description

Pulse LE - Ref. PLS200Rear Panel DescriptionRS-232 communication port on a DB9 female connectorPower supply: IEC/EN/UL/CSA 60950-1, internal, autoswit

Page 4

Going further with the Pulse LEFor complete details and operations procedures, please refer to the Pulse LE User’s Manual and our website for further